what is tbe best product to fill in panneling grooves

Making wood paneling look similar drywall is an easy projection that about anyone can exercise. Turning your paneled walls into a smooth wall gives the room a much more modern, updated look.

This post may comprise affiliate links. If you have any questions, please encounter my disclaimer folio.

How To Make Wood Paneled Walls Look Like Drywall

To brand your paneling await a smoothen wall, you need to fill in the seams. If y'all have a large surface area that has wood paneling, this volition accept a bit of time, but the results are amazing.

Here is my wall before and after I filled in the seams:

Yous would never know that this wall was actually forest paneling.

Here are the steps to making your forest paneled walls look similar a shine wall.

Stride one: Prime the paneling.

To start, I primed the surface area using a loftier quality primer. I like to apply PrepRite ProBlock from Sherwin Williams because it is designed for smoothen surfaces.

Paint the whole area with the primer before y'all do annihilation else. This will give the articulation chemical compound and paint a good surface to stick to.

I glaze of primer on the paneling is enough to create a workable surface for the next step.

Footstep ii: Employ joint chemical compound to the grooves in the wood paneling.

After the primer has dried, get a spackle brush and your joint compound.

Using your spackle castor, fill in the grooves of the paneling. Apply articulation compound over the whole groove from acme to bottom (or bottom to elevation if you prefer). Using a house hand, scrape off as much of the joint chemical compound equally possible in long strokes. This will allow the articulation compound to remain only in the groove.

Y'all want to scrape off basically all of the joint compound, except what is in the groove. Exist careful not to catch the edge of your spackle brush on the wall, equally information technology volition likely pull the primer off.

Wait until your joint compound dried. This may have a full 24 hours, depending on the product you apply.

It is likely that your joint chemical compound shrank down some and there is still a slight groove in your paneled wall. If so, apply a 2d glaze of joint chemical compound using the same technique.

This is how my wall looked after two coats of joint chemical compound.

Once again, wait until the articulation chemical compound is fully dry. Apply a third glaze of joint chemical compound if the previous coat sank into the grooves.

To test if your joint compound sank into the lines of the paneling, close your eyes and run your fingertips across the groove. If y'all experience nothing, you're done. If you yet feel a small groove, apply another coat of articulation compound.

When I filled my wood paneling grooves with joint compound, it took three coats to fill up the lines to be completely smoothen.

What to utilize to make full in paneling grooves?

This production, made past USG, is a slap-up selection for filling in paneling grooves. It is actually easy to work with because information technology comes pre-mixed. This ways that there is no approximate work involved in figuring out how much water to add to the articulation compound, because everything is already in the bucket.

Plus, the dust control aspect of it ways that it comes off in clumps when y'all sand information technology. Because of this, it is much more probable to fall to the ground instead of spreading throughout your whole house.

At present, you volition nonetheless become dust all over if y'all sand any type of drywall chemical compound, but not nearly as much if you apply a grit command product.

If you really want to almost eliminate the grit in your home, choice up one of these drywall sanding attachments for your store vac.

Because the sander is attached to the vacuum hose, it works really well for sucking upwards all the drywall dust produced by sanding.

Step 3: Sand the Joint Compound.

In one case the articulation chemical compound is fully dry out, lightly sand whatever high spots. Ideally, you lot won't take too much chemical compound on the flat sections of paneling, and y'all won't need to do much sanding.

If you do need to sand, sand the edges of your joint compound in a light, circular motion.

Stride 4: Prime The Paneled Walls. Over again.

I know this seems redundant, simply this is actually really important in making your forest paneling expect like drywall.

Joint compound makes the sheen of paint announced unlike than in places that don't have it. So, for this reason, you need to prime the whole wall again.

If you skipped this step, you paint would await striped. The paint that is on the joint compound where the grooves were would await like more of a matte cease and the paint in between the grooves would look shinier. And so don't skip this step.

Footstep 5: Paint the Walls.

Finish your walls with ii coats of your favorite pigment, just like you lot would if you lot were painting bodily drywall.

Curlicue the walls with a 3/8 inch nap roller, and cut in the edges with a good quality, angled brush.

For a paint recommendation, I similar Sherwin Williams Super Paint because information technology has actually dandy coverage.

If you need some tips, check out this mail service on how to pigment a room.

Concluding Thoughts on Making Woods Paneled Walls Look Like Drywall

Filling in the grooves of your wood paneled walls to make them look smooth is a great way to update your room. It gives the space a much more than modern look. Plus, the room ends up looking bright and fresh from new paint equally well.

Here is how my wood paneled wall transformation turned out.

This DIY project took me almost 3 days to complete, only only considering the joint chemical compound takes a long time to dry. The full active time for this project was peradventure 4 hours.

If you want to completely update the look of your wood paneled room, filling in the grooves to make the walls look like drywall is a corking way to do it!

Want to run into all your paint options in 1 convenient identify? Click here to pick up a Sherwin Williams fan deck (contains all SW colors) or a Benjamin Moore Collections fan deck (contains many popular BM colors – other fan decks sold separately)!

daveyfingrifuread.blogspot.com

Source: https://www.loveremodeled.com/make-wood-paneling-look-like-drywall/

Share this post